This post contains a few options related to a factory default configuration on a Cisco ASA 5505. The first part shows how to reset the ASA to factory default configuration from the CLI and the commands that are automatically executed once you press enter. The second part is just a clean, fresh from the factory configuration.
asa2(config)# configure factory-default
Based on the inside IP address and mask, the DHCP address
pool size is reduced to 250 from the platform limit 256
WARNING: The boot system configuration will be cleared.
The first image found in disk0:/ will be used to boot the
system on the next reload.
Verify there is a valid image on disk0:/ or the system will
not boot.
Begin to apply factory-default configuration:
Clear all configuration
Executing command: interface Ethernet 0/0
Executing command: switchport access vlan 2
Executing command: no shutdown
Executing command: exit
Executing command: interface Ethernet 0/1
Executing command: switchport access vlan 1
Executing command: no shutdown
Executing command: exit
Executing command: interface Ethernet 0/2
Executing command: switchport access vlan 1
Executing command: no shutdown
Executing command: exit
Executing command: interface Ethernet 0/3
Executing command: switchport access vlan 1
Executing command: no shutdown
Executing command: exit
Executing command: interface Ethernet 0/4
Executing command: switchport access vlan 1
Executing command: no shutdown
Executing command: exit
Executing command: interface Ethernet 0/5
Executing command: switchport access vlan 1
Executing command: no shutdown
Executing command: exit
Executing command: interface Ethernet 0/6
Executing command: switchport access vlan 1
Executing command: no shutdown
Executing command: exit
Executing command: interface Ethernet 0/7
Executing command: switchport access vlan 1
Executing command: no shutdown
Executing command: exit
Executing command: interface vlan2
Executing command: nameif outside
INFO: Security level for "outside" set to 0 by default.
Executing command: no shutdown
Executing command: ip address dhcp setroute
Executing command: exit
Executing command: interface vlan1
Executing command: nameif inside
INFO: Security level for "inside" set to 100 by default.
Executing command: ip address 192.168.1.1 255.255.255.0
Executing command: security-level 100
Executing command: allow-ssc-mgmt
ERROR: SSC card is not available
Executing command: no shutdown
Executing command: exit
Executing command: object network obj_any
Executing command: subnet 0.0.0.0 0.0.0.0
Executing command: nat (inside,outside) dynamic interface
Executing command: exit
Executing command: http server enable
Executing command: http 192.168.1.0 255.255.255.0 inside
Executing command: dhcpd address 192.168.1.5-192.168.1.254 inside
Executing command: dhcpd auto_config outside
Executing command: dhcpd enable inside
Executing command: logging asdm informational
Factory-default configuration is completed
ciscoasa(config)#
_______________________
ciscoasa# sh run
: Saved
:
ASA Version 8.4(1)
!
hostname ciscoasa
enable password mrc2YGsms0Df41/U encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
!
object network obj_any
nat (inside,outside) dynamic interface
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.1.5-192.168.1.254 inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
service-policy global_policy global
prompt hostname context
Cryptochecksum:5ee3fb383a35c98a6d5891329d759d6c
: end
ciscoasa#
